Home
Home Corona Treater Sleeves Drawdown Testing Stroboscopes Viscosity Measurement Other Products Site Information

Wet Film Thickness Gages

Type C and Type IC

Wet Film Thickness GageAccurately measures the wet film thickness of inks, coatings, gels, adhesives, paints, and almost any other wet film applied to flat or cylindrical surfaces

Meets ASTM D-1212

Accuracy certification meeting MIL STD 45662A is available

For any coating, thickness of application is of paramount importance: Too thin a film will exhibit poor hiding power and inadequate protective properties. Overly thick coatings inflate cost and often result in a loss in intended physical properties. These gages help ensure optimum coating performance at minimal cost. They are constructed as wheels consisting of three disk sections. Two of the disks are of the same diameter, and are concentric. The third disk is slightly smaller, and is eccentric to the two supporting disks. When the gage is rolled over a wet film, the eccentric disk (on center on type IC gages, and on the outside on type C gages) picks up the material only at and below the actual thickness, providing direct and immediate readings. Clean with appropriate solvent immediately after use. Optional certification is fully NIST traceable.

Type Total Range Recommended Usable Range Tolerance Code Price Quantity  
IC
0 - 1 mils
0.1 - 0.9 mils
0.1 mil
22001
$465.00
C
0 - 2 mils
0.2 - 1.8 mils
0.2 mil
22002
$395.00
C
0 - 4 mils
0.4 - 3.6 mils
0.2 mil
22004
$315.00
C
2 - 12 mils
3 - 11 mils
0.4 mil
22012
$298.50
C
10 - 30 mils
11 - 28 mils
0.5 mil
22030
$298.50
Optional Handle for Type C or IC Gage
22098
$278.50

NIST CERTIFIED

Type Total Range Recommended Usable Range Tolerance Code Price Quantity  
IC
0 - 1 mils
0.1 - 0.9 mils
0.1 mil
22071
$731.50
C
0 - 2 mils
0.2 - 1.8 mils
0.2 mil
22072
$538.50
C
0 - 4 mils
0.4 - 3.6 mils
0.2 mil
22074
$465.00
C
2 - 12 mils
3 - 11 mils
0.4 mil
22082
$448.50
C
10 - 30 mils
11 - 28 mils
0.5 mil
22090
$448.50

Notched Aluminum Wet Film Gages

Notched aluminum wet film thickness gage Simple, inexpensive, ASTMD-4414 approved;
28 increments – 1 to 80 mils

Average dimensional accuracy +/- 0.2 mils (5 microns). Measures wet film thickness on any flat, smooth surface. Micron scale and full instructions printed on back side. 2.25" x 3.25" x .034" aluminum.

Quantity
Unit Price
1-5
$2.65
6-11
$2.15
12 - 47
$1.75
48 - 95
$1.50
>95
$1.40

Prod Code Quantity  
22101

Related Link: Drawdown Overniew

Diversified Enterprises
101 Mulberry St., Suite 2N, Claremont, NH 03743 U.S.A.
Phone 1-800-833-4644 (U.S.) or (603) 543-0038; fax (603) 543-1334
Send E-mail

© 2014 Diversified Enterprises, All rights reserved.

resources

Other related sites from Diversified Enterprises:

AccuDyneTest.com
Dyne testing, contact angle meters, and tensiometers.
A most comprehensive collection of information on dyne testing and surface energy analysis

bottom rounded
resources
Login
Username:
Password:

(Note: You must have an account and be logged in to purchase through this cart)

create account
lost password?

bottom rounded
resources

no items in cart

bottom rounded

 

Sales Terms (USA)
Sales Terms (International)
Shipping Information
Lost Password Help
Site Map